JDM specialist Japanparts.com

For BLITZ DAMPER ZZ-R series. Spec: (VEHICELE) / (MY) / (MODEL) / (ENGINE) /(Camber adjustable range)/(DAMPER ZZ-R height adjustable range) ALPHARD 2WD / 01.2015-01.2018 / AGH30W / 2AR-FE / -3° 30' - -2° 00' / -80 - -35 * ALPHARD 2WD / 01.2015-01.2018 / GGH30W / 2GR-FE / -3° 30' - -2° 00' / -85 - -40 * ALPHARD 2WD / 01.2018- / AGH30W / 2AR-FE / -3° 30' - -2° 00' / -80 - -35 * ALPHARD 2WD / 01.2018- / GGH30W / 2GR-FKS / -3° 30' - -2° 00' / -85 - -40 * VELLFIRE 2WD / 01.2015-01.2018 / AGH30W / 2AR-FE / -3° 30' - -2° 00' / -80 - -35 * VELLFIRE 2WD / 01.2015-01.2018 / GGH30W / 2GR-FE / -3° 30' - -2° 00' / -85 - -40 * VELLFIRE 2WD / 01.2018- / AGH30W / 2AR-FE / -3° 30' - -2° 00' / -80 - -35 * VELLFIRE 2WD / 01.2018- / GGH30W / 2GR-FKS / -3° 30' - -2° 00' / -85 - -40 * Remarks: Please install using the included spring. OEM stock wheel cannot be installed. Can be installed on side lift up seats Since the wheelbase is 3000mm, a minimum ground clearance of 100mm or more is required. * The camber adjustable range is the measured value when the camber is adjusted only with this product. * The vehicle height adjustment range is the data when the DAMPER ZZ-R is installed. * MIRACLE STROKE ADJUSTER can also be attached to "DAMPER ZZ-R BB". If it is installed due to the characteristics of this product, the minimum ground clearance may not be achieved because the vehicle height is lowered. When using this product and attaching a camber, it is necessary to adjust the toe to an appropriate value. For use outside the range of genuine toe adjustment, a separate toe adjustment arm may be required. Products and prices are subject to change without notice for improvement. In addition, the above models may be discontinued without notice. The camber adjustable range and vehicle height adjustable range may vary depending on individual vehicle differences and equipment. BLITZ MIRACLE STROKE ADJUSTER Features: - Optimizing the position of the lower arm, can be further ensured effective stroke of the spring, DAMPER ZZ-R series dedicated for the rear adjuster. - The width of the alignment is spread, suppression and of uneven wear, improvement of driving performance, a number of benefits, such as improved ride quality can be expected. - To eliminate some common stroke shortage at the time of Lowdown, also achieved a miraculous ride at a lower ride height. - The hole shape and dedicated bolt accordingly the vehicle type dedicated bracket employing the eccentric cam, can be finely adjusted camber angle. - Rear coil-over by optimizing the position of the lower arm, improved running performance by extending the same time movement of the suspension and to correct the roll center.

Spec: Caliper: Aluminum forged 6POT in metallic red Disc: φ355 / 2pc, with slit Pad: Non-asbestos ceramic composite, Rotor proper temperature range 0-450°C, Average friction coefficient 0.40 to 0.47µ Hose: Includes exclusive stainless steel mesh Teflon brake hose. A cover is attached to the mesh hose and socket joint, and the dynamic stress on the caulked part is reduced and the durability is greatly improved. In addition, the fixing of the middle part of the hose also uses a exclusive metal fitting, which enables reliable attachment. For BRZ Model ZC6, Eng. FA20. Remarks:This kit contains all the parts needed for installation, but does not contain chemicals such as brake fluid and brake grease. - By installing this kit, you can not attach a genuine wheel. Please verify in advance whether the clearance of the wheel to be attached can be secured in advance. - Processing of the back plate is required. Although the processing method is free, please be careful not to deform the remaining part or leave a piece in the vehicle. - The front center bell housing is anodized (some models only). Alumite may peel off or fade away due to continuous high temperature conditions caused by circuit driving etc. Please note that there is no impact on performance. - Due to the nature of the pad when it is cold or when the brake pad is wet, brake noise may occur, but this is not a malfunction. BLITZ BIG CALIPER KIT II Features: - New designed brake caliper kit by exclusive model for further high braking ability and controllability. - High-level "lightweight" and "high rigidity" by forging. - Slit rotors realize high "heat dissipation". The fade phenomenon is suppressed and the braking force of the pad is kept in the optimum condition. - Includes exclusive stainless steel mesh teflon brake hose. - A bright metallic red calipers and black bell housings. - Two types are available.     1) For street use, low-dust, quieter and reduced rotor aggression.     2) For racing use, superior in initial braking and enables higher braking power. The racing use has realized about 7% more braking power than the street use.

NUR-SPEC CUSTOM EDITION option part. Tail Diameter: φ101.6 Insertion diameter: φ52 Tip Material: Carbon Red

NUR-SPEC CUSTOM EDITION option part. Tail Diameter: φ101.6 Insertion diameter: φ52 Tip Material: Stainless, mirror finished

NUR-SPEC CUSTOM EDITION option part. Tail Diameter: φ114.3 Insertion diameter: φ62 Tip Material: Carbon Red

NUR-SPEC CUSTOM EDITION option part. Tail Diameter: φ114.3 Insertion diameter: φ62 Tip Material: Stainless

Only for EJ20 STi version 5-6, SF5/B-D (Impossible to use with TRC models) and BE5/BH5 (Impossible to use with TRC models). Boost pressure (accelerator off time) goes back to suction as stock. Material: Aluminum die casting

　to check BLITZ HP Note: - It is possible malfunctions some devises with radar, camera, sensor etc. by installing DAMPER ZZ - R series. It is also possible that malfunctions such as safety equipment, collision avoidance support equipment, driving assistance equipment of each car manufacturer may occur. - When installing the DAMPER ZZ-R series, especially in the case of the strut type suspension, the shock absorber may interfere with even genuine wheels and tires. Note: This item may require an extra shipping charge depending on the destination country. If it does, we will contact you by email within 3 business days after the order is placed and tell you how much extra it costs for shipping. You can ask us to cancel the order if you would not like to pay the difference. We will proceed with the order once we receive the extra payment from you.

at the same time provide sufficient cooling to prevent the turbine damage.

Tip Piece: 1 Position: Only one side Design: Circle, Inner curl Tip Material: Titanium Tip O.D.: 120-2.5R Pipe Size: 60-70 Consist of: 1 Close Sound Level (OEM/BLITZ): 82 / 95 For 86, ZN6, FA20 engine, MY 04/2012 - Remarks: Also for the vehicles equipped TRD rear bumper spoiler/TRD rear garnish, For the model before M/C and after M/C , Incompatible the vehicle equipped BLITZ Rear Diffuser, For MT , Meets new Japanese regulation NUR-SPEC F-Ti Features: - All-titanium exhaust system. - The high spec model is lightweight and excellent in corrosion resistance. Also the titanium material minimizes the effect of heat.