Spec:
Caliper: Aluminum forged 4POT in metallic red
Disc: φ330 / 1pc, with slit
Pad: Non-asbestos ceramic composite, Rotor proper temperature range 0-450°C, Average friction coefficient 0.40 to 0.47µ
Hose:
Includes exclusive stainless steel mesh Teflon brake hose. A cover is attached to the mesh hose and socket joint, and the dynamic stress on the caulked part is reduced and the durability is greatly improved. In addition, the fixing of the middle part of the hose also uses a exclusive metal fitting, which enables reliable attachment.
For Civic Sedan, MY 09/2017 -, Model FC1, Eng. L15B, For Civic Hatchback, MY 09/2017 -, Model FK7, Eng. L15C.
Remarks:This kit contains all the parts needed for installation, but does not contain chemicals such as brake fluid and brake grease.
- By installing this kit, you can not attach a genuine wheel. Please verify in advance whether the clearance of the wheel to be attached can be secured in advance.
- Processing of the back plate is required. Although the processing method is free, please be careful not to deform the remaining part or leave a piece in the vehicle.
- The front center bell housing is anodized (some models only). Alumite may peel off or fade away due to continuous high temperature conditions caused by circuit driving etc. Please note that there is no impact on performance.
- Due to the nature of the pad when it is cold or when the brake pad is wet, brake noise may occur, but this is not a malfunction.
BLITZ BIG CALIPER KIT II Features:
- New designed brake caliper kit by exclusive model for further high braking ability and controllability.
- High-level "lightweight" and "high rigidity" by forging.
- Slit rotors realize high "heat dissipation". The fade phenomenon is suppressed and the braking force of the pad is kept in the optimum condition.
- Includes exclusive stainless steel mesh teflon brake hose.
- A bright metallic red calipers and black bell housings.
- Two types are available.
1) For street use, low-dust, quieter and reduced rotor aggression.
2) For racing use, superior in initial braking and enables higher braking power. The racing use has realized about 7% more braking power than the street use.
M12xP1.5 20pc
Base diameter: 20mm, Bearing surface: 60° taper, Weight: (with aluminum cap )approx. 27g each
Exclusive adapter and hexagon wrench included.
For Lancer Evolution CN9A / CP9A / CT9A / CT9W / CZ4A . Incompatible with vehicles with genuine wheels
P.N. Red ZZTN52-20R, Black ZZTN52-20BK
Note:
- You can not attach a wheel whose bearing surface is a flat seat or spherical seat.
- If the contact surface of the wheel nut is not tapered (such as genuine wheel etc.) it can not be mounted.
- It does not fit to the wheel bolt specification car.
- When the cap is attached, the effective screw length of this product is 20 mm. In advance, make sure that there is no shortage of thread allowance and bottoming of the vehicle hub bolt.
- Make sure that the nut fits inside the fender line.
- Even if the nut fits inside the fender, if it protrudes from the outermost part of the wheel rim, it may be pointed out.(such as a sharp projection).
- If the wheel offset spacer is not used in combination with the long hub bolt mounting vehicle, the caps can not be attached because the hub bolt is bottomed.
monster SPORT HEPTAGONAL WHEEL NUT Type2 Features:
- Theft prevention function
By using the heptagonal design, it has an anti-theft function.
- Light weight & high strength
The material used is chromium vanadium steel, which does not easily loosen even at high temperatures, for both of strength and small size weight reduction.
- Dedicated aluminum cap
Equipped with a colored anodized aluminum cut-out cap on the tip, it can also be removed. Giving nice accent to the wheel.
- Compact size
The total length of the wheel nut has been reduced to 28 mm (compared to the conventional heptagon wheel nut -4mm).It is also recommended for vehicles with protrusion tight clearances, such as compact cars and small cars.
- Brand logo
The logo of "MONSTER SPORT" was printed on each of the aluminum cap and nut body.
With STi logo. Tail pipe diameter: 70mm. Comes with gaskets and so on. Please choose the model from (#STPKG40GH020) e-BOXER or (#STPKG40GH011) except e-BOXER
0 Item
Please reload your browser if the view type does not change.
